![]() Say, you measure the thicknesses of the stems of n, o, H and O, and you get 50, 56, 62 and 68, it is best to enter only one average value of 60. So, try to use only one good average value that more or less fits all your letters. The idea is that if one letter uses, e.g., two pixels for its stems, all the other letters use two pixels as well. This value will be used to unify and harmonize the number of pixels used to display the thicknesses of vertical stems in low-resolution circumstances. Vertical Stems: The average thickness of your vertical stems.If, on the other hand, your font is a symbol or dingbat font, or does something fancy with its outlines, like a grunge font, it is better to skip the two stems settings. has no special effects like roughened outlines, inlines, flourishes, very fine details, dashed and dotted lines, many nodes (more than a dozen or two), etc.prioritises legibility over shape fidelity,.is a regular text letter design with recurring, similar shapes in its letters (what most people would call a ‘normal font’),.your design has extremum points set ( Glyph > Add Extremes),.If your font does not lend itself for hinting, you can leave these blank. The following two settings, the standard stems, are only important for hinting and a few functions like Open Corner form the context menu. If your design does not have lowercase letters or maybe not even any letters at all, as in an icon font, it is a good idea to leave this value at its default -200. In italic designs, letters like f and the German sharp ß sometimes also have descenders. Descender: A negative number value representing the depth of lowercase letters with descenders, such as g, j, p, q, y, and the Icelandic þ, again not counting overshoots.Typically, ascender heights are somewhere between 700 and 800. If you have a design that reverses that relationship, i.e., caps are higher than ascenders, consider using the Ascender value for your caps, and vice versa. (Note: the lowercase t usually exceeds the x-height, but does not reach the ascender.) These letters are typically the highest (unaccented) letters in a type design, also exceeding your cap height. Ascender: The height of lowercase letters with an ascender, such as lowercase b, d, f, h, k, l, or the Icelandic þ and ð, not counting overshoots.Typical x-heights are around 500 units tall, give or take a few. If you do not have lowercase letters in your font, make sure it is a value lower than the cap height. x-Height: The height of lowercase letters without an ascender, again, best measured in designs that do not have overshoots, like lowercase x, v, w, y or z.If your font is an icon font, it is best to leave it at the default of 700. If your design is much larger, consider changing Units per Em value in the bottom right corner to something that encompasses both cap height and descender. Most type designs have values between 600 and 700. Cap Height: The height of your capital letters, best measured at a straight and simple letter without overshoots, e.g., uppercase H, T or I.For instance, apps calculate the first baseline offset based on these numbers. These settings describe some important measurements of your font and influence how your font is displayed in some apps. Again, keep the style name short, and stick to plain ASCII. But you can have unconventional names as well, like Grunge, Supercool, Dotted, or Laser, whatever describes your design best. Typical style names are Light, Regular, Book, Medium, Semibold, Bold, Heavy, Black and Light Italic, Italic, Book Italic, Medium Italic, Semibold Italic, Bold Italic, Heavy Italic, Black Italic, you get the idea. Very much like brothers and sisters need different first names if they have the same family name. If multiple fonts do share the same family name, they have to be differentiated with style names. Style Name: on the right, by default ‘Regular’. Some apps may complain, list the font wrongly or not at all. Also for maximum compatibility, it is best to start the family name with a letter (A-Z, a-z), even though it is technically possible to start with a figure (0-9). For maximum compatibility, it is advisable to avoid a dash in the family name as well. No umlauts, accents or other non-ASCII special characters. You can use capitalization and word spaces, but do keep the family name short (less than 20 characters in total), and only use ASCII (A-Z, a-z, 0-9). If multiple fonts share the same family name, they are grouped in the same font submenu, for instance in the font menus of apps like Adobe InDesign. They are the big letters on grey background at the top of the tab.įont Family Name: The words on the left, by default ‘new Font’, are your Font Family Name. The most important settings in your Font Info are two names: the Font Family Name and the Style Name.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |